Wood Carving Information

Wood carving (xyloglyphy) is a form of working wood by means of a cutting tool (knife) in one hand or a chisel by two hands or with one hand on a chisel and one hand on a mallet, resulting in a wooden figure or figurine, or in the sculptural ornamentation of a wooden object. The phrase may also refer to the finished product, from individual sculptures, to hand-worked mouldings composing part of a tracery.

Some of the finest extant examples of early wood carving are from the Middle Ages in Italy and France, where the typical themes of that era were Christian iconography. In England many complete examples remain from the 16th and 17th century, where oak was the preferred medium in this case

Figural carving seems to have been widespread. The carving to represent one's god in a tangible form finds expression in numberless ways. The early carver, and, for that matter, the native of the present day, has found a difficulty in giving expression to the eye, and at times has evaded it by inlaying this feature with colored material.

Methods and styles

• Chip carving
• Relief carving
• Scandinavian flat-plane
• Caricature carving
• Lovespoon
• Treen
• Whittling

Techniques

Tools

• Carving Knives

• Carving Knife used to round a corner of a piece of wood

• V-Tool used to part lines and cut V shaped channels

Basic tool set

• the carving knife: a specialized knife used to pare, cut, and smooth wood.
• the gouge: a tool with a curved cutting edge used in a variety of forms and sizes for carving hollows, rounds and sweeping curves.
• the coping saw, a small saw that is used to cut off chunks of wood at once.
• the chisel, large and small, whose straight cutting edge is used for lines and cleaning up flat surfaces.
• the V-tool used for parting, and in certain classes of flat work for emphasizing lines.
• the veiner: a specialized deep gouge with a U shaped cutting edge.
• sharpening equipment, such as various stones and a strop, necessary for maintaining edges.

A special screw for fixing work to the workbench, and a mallet, complete the carvers kit, though other tools, both specialized and adapted, are often used, such as a router for bringing grounds to a uniform level, bent gouges and bent chisels for cutting hollows too deep for the ordinary tool.

Wood

Selection

The nature of the wood being carved limits the scope of the carver in that wood is not equally strong in all directions: it is an anisotropic material. The direction in which wood is strongest is called "grain" (grain may be straight, interlocked, wavy or fiddleback, etc.). It is smart to arrange the more delicate parts of a design along the grain instead of across it, and the more slender stalks or leaf-points should not be too much separated from their adjacent surroundings. The failure to appreciate these primary rules may constantly be seen in damaged work, when it will be noticed that, whereas tendrils, tips of birds beaks, etc., arranged across the grain have been broken away, similar details designed more in harmony with the growth of the wood and not too deeply undercut remain intact. Probably the two most common woods used for carving are Basswood (aka Tilia or Lime) and Tupelo, both are hardwoods that are relatively easy to work with. Chestnut, Butternut, Oak, American walnut, mahogany and teak are also very good woods; while for fine work Italian walnut, sycamore maple, apple, pear, box or plum, are usually chosen. Decoration that is to be painted and of not too delicate a nature is as a rule carved in pine.

Sculpture

A wood carver begins a new carving by selecting a chunk of wood the approximate size and shape of the figure he or she wishes to create or, if the carving is to be large, several pieces of wood may be laminated together to create the required size. The type of wood is important. Hardwoods are more difficult to shape but have greater luster and longevity. Softer woods may be easier to carve, but are less resistant to damage. Any wood can be carved but they all have different qualities and characteristics. The choice will depend on the requirements of carving being done: for example a detailed figure would need a wood with a fine grain and very little figure as strong figure can interfere with 'reading' fine detail.Once the sculptor has selected their wood, he or she begins a general shaping process using gouges of various sizes. The gouge is a curved blade that can remove large portions of wood smoothly. For harder woods, the sculptor may use gouges sharpened with stronger bevels, about 35 degrees,and a mallet similar to a stone carver's. The terms 'gouge' and 'chisel' are open to confusion. Correctly, a gouge is a tool with a curved cross section and a chisel is a tool with a flat cross section. However, professional carvers tend to refer to them all as 'chisels'. Smaller sculptures may require the wood carver to use a knife, and larger pieces might require the use of a saw. No matter what wood is selected or tool used, the wood sculptor must always carve either across or with the grain of the wood, never against the grain.

Once the general shape is made, the carver may use a variety of tools for creating details. For example, a “veiner” or 'fluter' can be used to make deep gouges into the surface, or a “v-tool” for making fine lines or decorative cuts. Once the finer details have been added, the wood carver finishes the surface. The method chosen depends on the required quality of surface finish. The texture left by shallow gouges gives 'life' to the carving's surface and many carvers prefere this 'tooled' finish. If a completely smooth surface is required general smoothing can be done with tools such as “rasps,” which are flat-bladed tools with a surface of pointed teeth. “Rifflers” are similar to rasps, but smaller, usually double ended, and of various shapes for working in folds or crevasses. The finer polishing is done with abrasive paper. Large grained paper with a rougher surface is used first, with the sculptor then using finer grained paper that can make the surface of the sculpture slick to the touch.

After the carving and finishing is completed, the artist may seal & color the wood with a variety of natural oils, such as walnut or linseed oil which protects the wood from dirt and moisture. Oil also imparts a sheen to the wood which, by reflecting light, helps the observer 'read' the form. Carvers seldom use gloss varnish as it creates too shiny a surface, which reflects so much light it can confuse the form; carvers refer to this as 'the toffee apple effect'. Objects made of wood are frequently finished with a layer of wax, which protects the wood and gives a soft lusterous sheen. A wax finish is comparatively fragile though and only suitable for indoor carvings.

Traditions

The making of decoys and fish carving are two of the artistic traditions that use wood carvings.

See also

• List of woodcarvers
• Chainsaw carving
• History of wood carving
• Wood as a medium
• Woodcut
• Woodturning
• Woodworking
• Woodcarved catholic saints in the Parish Church of Ortisei
• National Wood Carvers Association

Gallery

• From Africa

• from Austria

• Chinese wooden bodhisattva, 12th to 13th century.

• Tilman Riemenschneider's Saint Barbara from Germany

• in Festac Town, Lagos, Nigeria

• in Festac Town, Lagos, Nigeria

• Carved gallant genre scene with figurines from Val Gardena 18th century

• Pensive Christ in a Lithuanian cemetery

• Sculpture by Medina Ayllón.(Spain)

• Carving of a duck by a Florida artist

• Carving of unicorn by G&H Studios

• circa 1940s, hobo by Carl Johan Trygg

• The eponymous carving on the Urnes stave church is an example of the Urnes style.(Norway)

• Oseberg ship head post.

• Wood crafted lamp

• Wooden crafted mirror frame

References

• This article incorporates text from a publication now in the public domain: Chisholm, Hugh, ed. (1911). Encyclopædia Britannica (11th ed.). Cambridge University Press.
• This article incorporates public domain material from websites or documents of the National Archives and Records Administration.

External links

• Chinese Wood Carving
• Woodcarving Magazine
• Sharpening, Honing and Polishing Gouges and Other Carving Tools by R.M Mottola
• The British Woodcarvers Association
• Maori Wood Carving

Categories:

• Woodcarving
• Woodworking

Related 'Wood Carving' Searches:

See Also:

• Arts: Crafts: Woodcraft: Woodworking: Project Plans
• History of Wood Carving
• Shopping: Tools: Woodworking: Wood Carving
• Wood
• Wood As a Medium
• Wood Carving
• Woodturning
• Woodworking
• Woodworking Classes Glens Falls Ny
• Woodworking Joints